Hörmann Torsion Spring Replacement is one of the most common calls we get. A technician will explain what is wrong and what it will cost before starting, and test the door before leaving. Torsion springs replaced and wound correctly, with high-cycle upgrades available. Our technicians service Hörmann garage doors regularly and know where the model and date labels are, which makes ordering the right part quicker. Hörmann is a German manufacturer of residential and commercial doors and openers with North American operations.
Safety first: springs and cables hold hundreds of pounds of tension. Don't try to adjust or remove them yourself, and don't run the opener on a door that's crooked or has a broken spring.
Signs you need Hörmann torsion spring replacement
- A gap in the spring mounted on the bar above the door
- The door slams shut or won't stay open
- Only one side of the door lifts and the door goes crooked
- The door is suddenly too heavy to lift by hand
Why this happens
- Normal fatigue at the end of the spring's rated cycles
- Rust or lack of lubrication
- An undersized spring working too hard
- A door that's been made heavier with insulation or new panels
Safe checks before you call
- Count the springs above the door. Two-spring doors should have both replaced together.
- Look for rust or dry, squeaky coils, which are signs the spring is wearing out.
- Note how often the door is used each day so the right cycle rating can be chosen.
Still stuck? Our free symptom checker and troubleshooting wizard walk you through it step by step.
How we handle Hörmann torsion spring replacement
- Clamp the door and unwind the old springs with proper winding bars
- Measure wire size, inside diameter and length, and weigh the door
- Install correctly rated springs, upgrading to high-cycle if you use the door a lot
- Wind to the right number of turns and set the door's balance
- Lubricate, adjust the cables and test the full travel
Wayne Dalton TorqueMaster doors keep the springs inside the torsion tube and need TorqueMaster-specific parts, which we can source.
Hörmann Torsion Spring Replacement cost in Merrimack, NH
What moves the price:
- Door size and weight (single or double, steel or wood)
- Which parts need replacing and whether they are in stock
- Spring type and cycle rating
- Emergency or after-hours timing
These are typical U.S. ranges, not a quote. You get an exact price for your door before any work starts. For a quick estimate, try the repair cost calculator.
Other Hörmann services
- Hörmann Garage Door Repair
- Hörmann Extension Spring Replacement
- Hörmann Garage Door Cable Repair
- Hörmann Garage Door Roller Replacement
- Hörmann Garage Door Track Repair
- Hörmann Off-Track Garage Door Repair
- Hörmann Garage Door Panel Replacement
- Hörmann Weather Seal Replacement
- Hörmann Garage Door Installation
- Hörmann Garage Door Opener Repair
- Hörmann Garage Door Opener Installation
- Hörmann Smart Garage Door Opener Setup
- Hörmann Remote & Keypad Programming
- Hörmann Garage Door Sensor Repair
- Hörmann Opener Gear & Sprocket Replacement
- Hörmann Opener Circuit Board Replacement
Serving Merrimack, NH and nearby towns
In New Hampshire, spring failures spike during cold snaps, when worn steel is at its most brittle. If your springs are near the end of their cycle life, replacing them before winter is cheaper than an emergency call on the coldest morning of the year.
Close to the coast, salt air speeds up corrosion. Galvanized or coated springs, nylon rollers and stainless hardware hold up better than bare steel.
Besides Merrimack (ZIP code 03054), we handle Hörmann torsion spring replacement in East Merrimack (0.5 mi), Litchfield (1.6 mi), Bedford (5.7 mi) and Londonderry (6 mi). Call (833) 435-8883 to book a visit in Merrimack.
Hörmann Torsion Spring Replacement: frequently asked questions
How much does Hörmann torsion spring replacement cost in Merrimack, NH?
Hörmann Torsion Spring Replacement typically costs $200-$450 including parts and labor, and usually takes 1-2 hours. The exact price depends on your door and the parts it needs, and you get it before any work starts. Call (833) 435-8883 for a quote.
Can you do Hörmann torsion spring replacement the same day?
Often, yes. When a technician is available we can usually come the same day, and common parts are carried on the truck. Doors that won't close or have a broken spring are treated as priority calls, and emergency service is available.
Is Hörmann torsion spring replacement covered by a warranty?
Our work comes with a 90-day labor warranty on repairs. New parts and doors also carry the manufacturer's warranty, and Hörmann warranty terms vary by product and age. Ask for the warranty details in writing with your quote.
Are your technicians licensed and insured?
Our technicians are insured, and where New Hampshire or Merrimack requires a contractor license for garage door work, the job is done under that license. You're welcome to ask for proof when you book.
Should I repair or replace my garage door?
A good rule of thumb: if the repair costs more than about 50% of a replacement, or the garage door is near the end of its life, replace it. A garage door typically lasts 15 to 30 years. If several panels are damaged, the door is rusted through or rotted, or parts are discontinued, replacing it is often better value. Springs are the exception: a broken spring is always replaced, never repaired. Our free repair vs. replace calculator can help you compare.